Parts & Accessories
- Lock and unlock with special key - Lightweight aluminum key is easy to carry - Anti-rust CrMo axle, stainless steel springs
If wheel theft could be a problem, then these high-grade locking skewers and nuts will challenge even the most determined thieves. The KnoxNut features a one-of-a-kind nut protected by a super-tough free-floating outer ring, making it impossible to release your wheel with anything other than the special key. KnoxNuts can be installed on existing skewers or combined with the KnoxNut Skewer, a unique and unobtrusive blind-head cromoly skewer. The special forged key is lightweight and easy to carry. Use with regular 6mm allen key to unlock. All keys are marked with a unique serial number and replacement keys are only sold to consumers that have previously registered a key on deltacycle.com. Set Includes: - Front blind-head skewer with KnoxNut - Rear blind-head skewer with KnoxNut
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.
Original equipment freehub bodies to fit SRAM hubs and wheels.
Keep your skewers properly situated with these quality skewer springs from Salsa.
Salsa springs for Flip-Off skewers
- Replacement rear wheel skewer. - Specifically designed for use with Saris trainers. - Can be used for both indoor and outdoor rides.
Don't let a bent or worn dust cap sully an otherwise well-functioning Shimano Alfine internally geared hub. Get a spare and replace as necessary for continued performance and to preserve the longevity that you expect from Alfine.
Need a Shift Cable Fixing Bolt Unit for your Alfine S7000/S700 hub? Here it is. Now, get that bike back on the road!
Keeping contamination out of your internally geared hub is critical to its function and longevity. Sometimes, the oil port bolt comes loose and it's easy to lose, even if you've just taken it out to oil your hub. Keep a spare or two so your hub stays clean inside and it'll last you many, many miles.
New cones make hubs spin like silk. Take advantage of your Shimano Alfine hub's highly serviceable design, and replace the bearing cones if they are worn or damaged. This one is specifically for the right side.
This outer receiver unit works with the CJ-S700 Cassette Joint Unit for Shimano Alfine SG-S700 internally geared hub. This part can become worn, cracked, or torn, exposing the shift cable and possibly other components to unwanted dirt, water, mud, you name it. You don't want that.
If the bearings are getting rough on your Shimano Internally Geared hub, it could simply be a matter of replacing a pitted cone and repacking the bearing with grease. - Fits left side of Alfine SG-S700 hubs
Don't let a cracked or worn dust cap sully an otherwise well-functioning Shimano Alfine internally geared hub. Get a spare and replace as necessary for continued performance and to preserve the longevity that you expect from Alfine.
-Replacement left side cone and locknut for Shimano 105 FH-5800 rear hub
Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S7000 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S7000-8
Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S700 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S700
Add an Alfine hub, cog, spokes, and a rim to this Shimano Internally Geared Hub Small Parts Kit, and you're ready to rock. - Alfine hubs are packaged without small parts and require this kit plus a cog - Nexus hubs are packaged with small parts and cogs and do not require an additional small parts kit - For 11-Speed Hub - Includes CJ-S700 Cassette Joint for Vertical Dropouts *Cassette joint does not fit Di2 Alfine hubs
- Cassette Body Type: Shimano/SRAM 11 Speed Road - Material: Steel
Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.
$11.25 - $24.99
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$15.99 - $17.99
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair. Identifying your Hugo rim and selecting the correct valve stem: Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim. Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads: MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.
$23.99 - $29.99
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
Stan's Threaded Valve Extenders let you convert deep-section rims to tubeless. They're precision-machined from aluminum and are designed to fit deep-dish carbon and aluminum rims. And, they're threaded on the outside so you can install the Presta lock-ring nut for a perfect seal.
- Skewer Trek QR-18 100mm Bolt-On Front Black - Skewer Trek QR-18 135mm Bolt-On Rear Black
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Rear 10mm x 1 axle - Shimano Left Rear Cone - Cone Wrench Size: 15mm - Threads: 10mm x 1 - Cone Diameter: 17.0mm - Dust Seal Diameter: 25.5mm - Length: 16.0mm - 1 cone per bag COMPATIBLE HUBS: - XT M750, 9-spd Rear - XT M760, 9-spd Rear - XT M765, 9-spd Rear - Deore LX M570, 9-spd Rear
The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum - Similar to Fox Kabolt axle
The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum Not compatible with RS-1 fork